MFJ 989D Used Price & Fair Market Value

~$275
Fair market value
$275 (median of recent sales)
Typical range
$250 – $350
Based on
7 sold listings
Last updated
October 21, 2026

Values are estimates from recent comparable sales — condition, accessories, and included extras vary. Always compare before buying.

Selling your MFJ 989D? Run its Rig Check → Answer the questions a sharp buyer will ask and get a condition report for your listing — a fully answered report lets a truly nice radio demand a good price.

989D price history

$236$271$306$341$376 Dec '24 Oct '26 $300

Median sold price per month from 7 sold listings (Dec '24–Oct '26). Down ~14% over the period.

Recent sold listings

Date soldItemPriceStatus
Oct 2026MFJ-989D$300SOLD
Sep 2026MFJ-989D$250SOLD
Sep 2026MFJ-989D$275SOLD
Aug 2026MFJ-989D$275SOLD
Aug 2026MFJ-989D$250SOLD
Aug 2025MFJ-989D$295SOLD
Dec 2024MFJ-989D$350SOLD

Live 989D deals

No live below-market deals on this model right now — the good ones sell fast. Get the daily digest and you’ll see the next one before anyone else.

About the MFJ 989D

The MFJ-989D Versa Tuner V is MFJ's big manual antenna tuner — a roller-inductor T-network box rated at the full 1,500 watts SSB/CW across 1.8–30 MHz, including the WARC and MARS frequencies. It matches coax, wire, and balanced-line loads (there is a built-in 1:1 current balun), switches between two coaxial outputs, a wire/balanced output, and a built-in 300-watt 50-ohm dummy load, and meters through a peak-reading cross-needle SWR/wattmeter. The D version's selling points over the earlier 989s are the AirCore roller inductor with a fast-tune crank knob and a pair of 500 pF air-variable capacitors — double the capacitance of the earlier design, which MFJ credits for much more efficient operation on 160 and 80 meters. Our recorded sales put fair value around $275 on 7 in-window sales, so a genuine bargain sits under about $206. For a legal-limit station that runs more than one antenna and some balanced line, this is a lot of tuner for the used money — the design is simple, the parts are big, and there is nothing in it that can't be inspected with the cover off. That last point cuts both ways, and it's the whole used-buying story on this model. Buying used, run the roller inductor through its full travel and watch the turns counter while you do it. The best-documented owner complaint on the 989D is counter slippage: the plastic counter gears barely mesh because the mounting bracket isn't bent a full 90 degrees, so the counter drifts and any tuning chart you build on it becomes worthless (KV5R's detailed teardown calls the slip a flaw "many others, according to the reviews" also hit; his fix was realigning the bracket). A counter that won't repeat is a haggling point and a fixable flaw — but find it before you pay, not after you've charted a band. Also exercise the meter on both ranges (the same teardown documents RF getting into the metering board and pegging the reflected meter, fixed at the op-amp), check the capacitors' plates are centred and unbent, and respect the dummy load's limit: it's a 300-watt load, and the manual warns never to transmit into it with an amplifier. Ledger condition notes are mostly cosmetic ("a few minor scratches," "used once," "never more than 100W") — a unit that has genuinely only seen 100 watts is the one to pay up for.

Common questions

"The turns counter on my MFJ-989D slips and won't repeat — is that a known problem?"

Yes — it's the model's best-documented flaw. KV5R's teardown found the counter's plastic gears barely meshed because the L-bracket holding the counter was not bent a full 90 degrees, so the gear shaft sat misaligned; he notes many reviewers reported the same slip. The fix is mechanical: realign the bracket so the gears mesh fully (without pressing them so tight that tuning goes rough), then re-zero the counter with the roller fully counter-clockwise. Test repeatability before buying — roll to a setting, away, and back, and see if the counter and the match both return.

"Can I use the built-in dummy load with my amplifier?"

No. The built-in load is rated 300 watts, and the manual warns explicitly: never transmit into it with an amplifier. The tuner itself is rated 1,500 watts SSB/CW through to the antenna outputs — the dummy load is a rig-level test load, not a legal-limit one.

"Will the MFJ-989D tune balanced (ladder) line?"

Yes. Alongside two coaxial outputs it provides a wire/balanced-line output working through a built-in 1:1 current balun, and MFJ rates the tuner into balanced or unbalanced loads across 1.8–30 MHz. If you feed a doublet with ladder line, confirm the balun and the balanced terminals are in the deal and undamaged — they're the reason to pick this box over a coax-only tuner.

Get 989D deal alerts

Join the daily digest — one email a day when new below-market bargains are posted, including the MFJ 989D. No spam, unsubscribe anytime.

Other MFJ equipment